can we say traction?

http://www.geocities.com/twistedwedge12/wheelstand.html

Check these pics out, me and my buddy took his car to the track over the weekend..
pictures are a rough draft, better ones to come soon...

first off nice car

got a few questions what size tire is he runing, gears, and what tranny and convertor.

------------------
95 ta m6 lunati 383,pro performance stage 2 heads, gtp cam, spec clutch, holley 52, strange 12 bolt, tnt n20, hooker 1 3/4 long, 3 inch exh flowmaster,
452.0rwhp and 416.5 rwtq
676.8rwhp and 842.8rwtq on n2o

Did he have to go to the body shop to fix his bumper afterwords. http://web.camaross.com/bb/smile.gif What kind of tranny is he running? Also, what kind of cowl hood is he running (make and size)?
Thanks for the info
Matt

------------------
96 Camaro Z28 6spd., T-tops, custom viper red with pearlcoat paintjob and black top. Almost done with my combo for the low 10's...maybe a high 9!!
The Z under construction (http://udel.edu/~mattbaer)
92 Talon TSI 5spd. AWD Light Blue...some mods
Best E.T.-13.753@98.30mph
1.885 60ft.@13lbs boost

Trust me, the pic does not do this car justice. Holy ****, I thought he was going over backwards. Course his next run was a quite a bit lower, but he almost met the wall. I have a few questions, I meant to ask him this weekend, but didnt get a chance before you guys left. Anyhow what kind of suspension pieces is he running? Whats the details on his motor, what size shot of juice? Thanks!


P.S. Did he do any major damage to the car after landing that hard? Matt

nice man...thats a bad ass launch

Mike..you can see his car here
http://www.geocities.com/twistedwedge12/warren.html

Tim

------------------
95 firebird Blueprinted and ballanced 355, ported lt1 heads, custom cam motion solid roller,Moser 9" with 4.57's and a locker just to name a few.
11.23@122.25 1.579 60'

2001 NFRA LT1 NA Winner

More on www.geocities.com/herrint (http://www.geocities.com/herrint)

Talk about some massive torque from that nitrous

OneQuikZ: Suspension-HAL 12 ways and drag springs up front, PA tubular k-member and lower a-arms, Madman&Co manual rack, Madman Chrome Moly T/A, Out back-stock springs, competetion engineering 3-way shocks, hotchkis LCA&panhard bar, Airbags, Strange 12-bolt. Motor Work-Stock LT-1 block bored .030 w/2-bolt mains and stock crank. Eagle H-beam 6" rods, Ross pistons. LT-4 heads and intake by Total Engine Airflow, Comp Cams custom grind, TNT plate Nitrous kit, jetted to 300 hp. All this done on stock computer with reset rev limiter and re-calibration for the 30 lb injectors.

1fstTA- btw: your car is pretty sweet- He is running a 29.5 X10.5 ET Drag, A TH-400 trans with a custom built converter (stall around 3800, flash on juice is about 4400) He is running a 4.30 out back.

Nostang96z-The hood is a glasstek 4" cowl.

First off, speaking for Jason, thank for all the comments. I dont know if any of you guys were at the NFRA last year, but this is the car that won the LT-1 P/A class. The car would only get the wheels up about 1-1.5 feet last year. So, if anything is a true testament to how weight CAN make a whole hell of a lot of difference, I dont know what could prove better besides an actual E.T.


The car came down pretty hard after that launch, we think maybe the k-member is bent. Otherwise nothing was hurt, bewsides a nice scrape all along the underside of the back bumper, and lots of scrapes on the underside of the front bumper. He made a second attempt on the 150 pill and still carried the wheels to the 60-foot box about 4 feet up in the air (1.42 60-ft with rear tires), but the car veered to the right in the air, and when he came down it was very close to the center line..He had no choice but to cross over to the right lane, thankfully the guy he was racing was far back.

He thinks the time for some chassis tuning is about due, probably install a anti-roll bar. He might get travel limiters for the front, and also this car hasnt been weighed (nobody at the scales this weekend..he took about 250-275 off the car this winter, all was from drivers seat forward.), we think the weight distribution is a little off. So hopefully we will get all that lined out, and the car will launch moderately low (maybe 2-3 feet)and stay straight.

He was dissapointed only from the standpoint that he didnt get a timeslip!

After the race we went to Total Engine Airflow and put the car on the chassis dyno. The car made 698.4 RWHP and 754.2 RWTQ on the 300 shot. That is 873 HP and 942 TQ at the crank. Who says you need a big stroker motor to put down serious HP?


Hopefully more to come ASAP! Hopin for deep 9's.

[This message has been edited by twistedwedge (edited April 08, 2002).]

[This message has been edited by twistedwedge (edited April 10, 2002).]

DAMN!!!!!!!! That's Crazy HIGH.

IMPRESSIVE http://web.camaross.com/bb/biggrin.gif

That car is launching like Billingsley's old Camaro.

Jason will be in the 9's easily once the chassis is figured out. Glad he's ok. That's gotta be the highest 4th gen launch I've seen yet on here.

I've removed a lot of weight from my front end this year and now those pictures have me worried about my chassis setup. I hope I don't have the same problem when I hit the track.

------------------
Daren
9 sec convertible TA.
Homepage photos:http://photos.yahoo.com/daren96ta

man id really like to talk to this about his setup. can you get him to email me or send me his number id like to talk to him about his tranny and convertor.



------------------
95 ta m6 lunati 383,pro performance stage 2 heads, gtp cam, spec clutch, holley 52, strange 12 bolt, tnt n20, hooker 1 3/4 long, 3 inch exh flowmaster,
452.0rwhp and 416.5 rwtq
676.8rwhp and 842.8rwtq on n2o

<font face="Verdana, Arial" size="2">Originally posted by 1fstTA:
man id really like to talk to this about his setup. can you get him to email me or send me his number id like to talk to him about his tranny and convertor.


Ill talk to him and see what I can do.
</font>

<font face="Verdana, Arial" size="2">Originally posted by WIKIDTA:
DAMN!!!!!!!! That's Crazy HIGH.

IMPRESSIVE http://web.camaross.com/bb/biggrin.gif

That car is launching like Billingsley's old Camaro.

Jason will be in the 9's easily once the chassis is figured out. Glad he's ok. That's gotta be the highest 4th gen launch I've seen yet on here.

I've removed a lot of weight from my front end this year and now those pictures have me worried about my chassis setup. I hope I don't have the same problem when I hit the track.

</font>

All I have to say is dont under estimate what weight can do. Jasons car is exactly the same as last year except for the weight, gears and the slicks. Be prepared for anything...

Tell me, how does he get the front end of the car to come up so evenly on launch?

Randy

Thanks for the reply twisted! I have a couple of questions about that bada$$ ride. What is the race weight of it? What does that car run on the motor? Do you have any idea what the heads flow? Any N/A dyno numbers? That is a hell of a lot of horsepower to push through a th400 to the wheels. Very impressive
Matt

rje- it only came up straight the first time-the pics you saw on the 300 shot. The second time on the 150 shot, the car drifted and when he came down he had no choice but to cross over into the other lane to avoid a crash.

Nostang96z- he appreciates the comments-

We never got to weigh the car...nobody was at the scales.. it is estimated to be at 3250.

The heads were done by Total Engine Airflow, and I believe they flowed mid 290's on the intake and mid 230's on the exhaust. The exhaust ports were just "cleaned up" no major porting done there.(Room for improvement)

Since the car is set up for nitrous, he never has made a N/A pass with the auto, the car went a 7.53@95.5 1/8 when it was a stick car, slipping the clutch.

It dynoed 381.2 RWHP and 351.8 RWTQ on the motor.

[This message has been edited by twistedwedge (edited April 10, 2002).]

<font face="Verdana, Arial" size="2">Originally posted by twistedwedge:
All I have to say is dont under estimate what weight can do. Jasons car is exactly the same as last year except for the weight, gears and the slicks. Be prepared for anything...</font>

I don't think you can be prepared for that kind of a launch. Except maybe bring another pair of underwear with you.

I did something similar in weight reduction. Added an ARE K-member/A-arms, changed my Th400(2.75 first and 1.57 second gear ratios, low gear planetary [TCI 22750 gear set], removed some more excess weight in other areas, and added some race seats.

I think I might have made a mistake with my setup. The new planetary will provide me with a better take-off and improved low-end power. On the trans brake this could be a problem.

I take it Jason was on the brake on that pass?

Anyway, Jason's car is very impressive for only a 355 with a stock crank runing LT4 heads. Show's everyone that it can be done on a small motor. Hopefully the damage is minimal from that launch and you guys can make a full 9 sec 1/4 pass next time out.

Keep up the good work and hope to see you guys back on the track.

------------------
Daren
9 sec convertible TA.
Homepage photos:http://photos.yahoo.com/daren96ta

[This message has been edited by WIKIDTA (edited April 09, 2002).]

twisted wedge
What front springs did you install on the car? What holes are you in on the front and rear of the T/A????
Give me a call and I can give you some pointers on keeping it off the bumper.

------------------
Insanity at its fastest
Worlds Fastest Blown 4th Gen
9.18@ 152
First 9 sec. PROCHARGED F-Body
In Memory of TONY OWEN driver HYDROMANIA
www.madmanandcoracing.com

OMFG http://web.camaross.com/bb/eek.gif THAT IS INSANE!!!!!! http://web.camaross.com/bb/eek.gif

------------------
1994 Trans am GT
Borla cat back, 3:73's, Moroso CAI, 1LE bellows, SLP Ram air hood, LT4 KM, Chrome Firehawk Rims.
Race Trans built by LevelTen, 2600 LevelTen Torque Converter, Hotchkis STB, Edelbrock PHR
E.T. 13.93@100.43 with a slipping tranny and 80 degree heat

I want to start a new life, Get myself a sharp knife, Look into my own life, Kill things I don't like in me
-Ill Nino

[This message has been edited by kevkop94TA (edited April 10, 2002).]

What TNT kit is he using?

------------------
1993 Purple Pearl M6 Z28

Jackstand Queen

Picture 1 (http://pages.prodigy.net/barbarayoung1/_uimages/Untitled-7.jpg)
Picture 2 (http://pages.prodigy.net/barbarayoung1/_uimages/Untitled-4.jpg)
Picture 3 (http://pages.prodigy.net/barbarayoung1/_uimages/Untitled-6.jpg)

<font face="Verdana, Arial" size="2">Originally posted by Z-OwNEr:
What TNT kit is he using?

</font>

The LT-1 plate kit w/2 fogger nozzles that mounts between the TB and Intake

<font face="Verdana, Arial" size="2">Originally posted by twistedwedge:
The LT-1 plate kit w/2 fogger nozzles that mounts between the TB and Intake</font>

Have a link to where I can pick up a Kit like that? Was thinking about getting a TNT F-1 kit but not sure if it can be jetted bigger than a 150 shot.



------------------
1993 Purple Pearl M6 Z28

Jackstand Queen

Picture 1 (http://pages.prodigy.net/barbarayoung1/_uimages/Untitled-7.jpg)
Picture 2 (http://pages.prodigy.net/barbarayoung1/_uimages/Untitled-4.jpg)
Picture 3 (http://pages.prodigy.net/barbarayoung1/_uimages/Untitled-6.jpg)

<font face="Verdana, Arial" size="2">Originally posted by Z-OwNEr:
Have a link to where I can pick up a Kit like that? Was thinking about getting a TNT F-1 kit but not sure if it can be jetted bigger than a 150 shot.

</font>

www.nitrous-power.com (http://www.nitrous-power.com)

<font face="Verdana, Arial" size="2">Originally posted by twistedwedge:
www.nitrous-power.com (http://www.nitrous-power.com)</font>

Appreciate it.

The kit from TNT is called there Twister Plate System. ARE installed this system and saw excellent results with my combo http://web.camaross.com/bb/biggrin.gif


Great runs Jason. I may need to call Madman and look into that torque arm http://web.camaross.com/bb/wink.gif


------------------
Nick D'Agostino
**FOR SALE**
1997 Silver Camaro SS
ARE Built 396ci LT1
Moser 9" Rear End
HAL 12 Way Shocks
4L60E Race Built Trans
TNT Twister NO2 System

Best Times To Date
NA Time 12.37@109mph
NO2 Time 10.66@128mph

E-Mail For More Info


1995 Emerald Green Formula
Stock For Now
Times to Come


If you live life by the book, all you get is what has already been written.

I am a Proud Supporter of ......Boycott Lapeer Dragway

Any update on whats going on with the car?

<font face="Verdana, Arial" size="2">Originally posted by Z-OwNEr:
Any update on whats going on with the car? </font>

He is still waiting on our transmission guy to finish repairs.

The car now has a 10-point roll cage, adjustable panhard bar, travel limiters and anti-roll bar. Should have some times for you all in the next month at the latest..

------------------
1987 GTA- TH400 w/brake, 355, carbed, 11.3:1, TFS twisted wedge heads (non ported), Big Shot NOS, Lunati hyd roller .510/.525 lift 232/242 duration @.050, true dual 3" exhaust, hooker super comp 1 & 3/4" headers, flowmaster 2 chamber mufflers, no tailpipes, 6-pt roll bar strange 12-bolt w/ spool and 33 spline axles, BMR anti-roll bar, BMR LCA relocation brackets, BMR solid rod end panhard bar, PA tubular k-member and a-arms, PA coil over conversion, PA manual rack conversion, Weld Pro-Stars 15X10 w/28X12.5 ET Street out back, 15X3.5 out front

Best ET last year N/A,Stock suspension, on street tires, T56, stock rear end and 4.56's @ 3515 lbs: 12.46@115.1 (1/4) 8.15@90.5 (1/8)

drive it like you stole it!!

<font face="Verdana, Arial" size="2">Originally posted by twistedwedge:

The car came down pretty hard after that launch, we think maybe the k-member is bent. Otherwise nothing was hurt, bewsides a nice scrape all along the underside of the back bumper, and lots of scrapes on the underside of the front bumper...
</font>

Same thing happened to George Baxter. He was also using a madman TQ arm.